### Recent Posts

Pages: [1] 2 3 ... 10
1
##### Questions and Comments about Articles / Shelf life of 320PPM Colloidal Silver
« Last post by waboni on April 06, 2022, 07:10:13 PM »
Dear forum members, I made a batch of 320PPM colloidal silver last year, may be by june, it was glucose reduced and gel capped, stored in a dark place (inside a kitchen cabinet), now I was wondering if it is still safe to use. Have you experienced in calculating the maximum shelf life of this concentration colloidal silver?

Thanks a lot.
2
##### Articles -- Theory and Practice of Colloidal Silver / Calculating minimum cell voltage
« Last post by kephra on March 20, 2022, 10:20:34 AM »
When I started experimenting with production of colloidal silver, I tested various cell voltages, knowing that it must be greater than 3.5 which is the minimum voltage  required to reduce sodium and oxidize silver.  I did not see any increase in quality once I exceeded 10 volts, so I used 10 volts as a minimum voltage.

In a previous post, I stated that if you wanted to use a wider electrode spacing than 1.5 inches, you should increase the minimum cell voltage using this formula:
NewVoltage = 3.5 + 6.5 * NewSpacing/1.5
So for a 3 inch spacing, the minimum voltage would be 3.5+6.5*2 = 16.5 volts.
So why is it not 20 volts, when the spacing is now doubled?

The answer is that there are actually 4 electrodes in the cell, two physical, and two pseudo electrodes which are the bounday layers between the bulk water and the electrodes.  These pseudo electrodes are only a few nanometers ithick, and always produce the same voltage drop provided enough voltage is present.  This voltage drop at the silver anode through the boundary layer is 0.8 volts, and at the cathode is always 2.7 volts provided there is more than 2.7 + .8 volts available.  So changing the cell voltage only changes the voltage drop between the pseudo electrodes, and not the physical electrodes.  So the total cell voltage which you can measure with a voltmeter is 0.8 +6.5 +2.7 volts if you have 10 volts total.
The 6.5 volts in the bulk water is what moves the ions to and from the boundary layers where they interact with the physical electrodes.

To make the subject even more complicated, the boundary layers are actually composed of 5 sublayers, but that is irrelevant to this discussion.

 Spacing Min Volts -------------- -------------- 1.5 inch 10 volts 2  inch 12.2 volts 2.5  inch 14.3 volts 3 inch 16.5 volts
3
##### SilverTron Notes And Support Questions / Where is a my topic with invite
« Last post by wazzzem on February 10, 2021, 11:47:31 AM »
Where is a my topic with invite? Hmm i cant find it now ;/ wizz
4
« Last post by kephra on February 06, 2021, 03:05:50 PM »
Welcome to this forum!
5
##### Questions and Comments about Articles / HI Guys. Thanks for my approving
« Last post by wazzzem on February 06, 2021, 02:52:31 PM »
HI Guys. Thanks for my approving / wazz user, new user hehe
6
##### SilverTron Notes And Support Questions / Re: Deidre from Earth Clinic on the SilverTron Elite
« Last post by kephra on January 29, 2021, 09:56:12 PM »
7
##### SilverTron Notes And Support Questions / Where is Administration cgcsforum.com ??
« Last post by Antonioefo on January 29, 2021, 07:51:07 PM »
Where is moderator??
Regards.
8
##### SilverTron Notes And Support Questions / Re: Whats Inside the Elite V3
« Last post by kephra on January 29, 2021, 06:56:50 PM »
Why?
9
##### SilverTron Notes And Support Questions / Where is Administration cgcsforum.com ??
« Last post by Antonioefo on January 29, 2021, 06:35:09 PM »